Just how do you really feel in relation to How to Install a Bathtub?
Installing a bathtub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately challenging task. If the old tub is readily accessible, the task can relocate easily; if you have to open a wall surface to get rid of the old tub and position the new bathtub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will certainly require an assistant to move out the old tub as well as set in the brand-new one. Make sure you have qualified yourself for the job and fit attempting it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to consider utilizing one prior to you begin. Possibilities are you may need a professional plumber to make tube links.
This article will help you mount a brand-new bathtub in your shower room if you have actually currently purchased a brand-new bathtub as well as do not need to alter the setup of your previous water system pipelines.
Your tools and material checklist should consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water system. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be quite troublesome as a result of the restricted gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before carrying on to fit the new taps, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in area in between the tap as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap connectors. The previous kind should be connected to the faucet finishes initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the needed placement. The wood boards are practical in equally spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level reviews degree.
To install taps, fit the bottom of the outermost adaptable tap port to the proper supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the water system as well as inspect all joints and new pipework for leaks as well as tighten them if needed. Fill up the bath tub and additionally examine the overflow outlet and also the regular electrical outlet for leaks.
Finally, take care of the bath paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait up until the bath tub has actually been utilized a minimum of once as this will certainly resolve it into its last setting.
Getting ready for the Setup
First of all, the sustaining framework supplied with the bathroom must be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets system to avoid pressure on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its final position.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to fracture an inflexible seal, triggering the water to penetrate the wall surface in between the bathroom as well as the tiling, causing problems with dampness and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also fittings. They are offered in tubes and cartridges, and also are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can split relatively early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about How to Install a Bathtub Yourself, I was thinking sharing that piece was mandatory. Sharing is nice. Helping people is fun. Thank you for your time. Visit us again soon.
About